 |
Inventory Control System
Digital Fluid Management and Inventory Control
After ten years of successful service in Europe and over
four years of exemplary field tests here in the United
States and Canada, Samson offers Control Master - "the" PC
/ Windows based fluid inventory control system. Designed
for the modern shop environment, it is de-centralized
to facilitate faster and more efficient work flow. This
system provides "instant access" for the technicians
via conveniently located keypads on the shop floor, while
continuously monitoring the system and displaying transactions
on the PC at the parts counter or other PC locations.
For management, a completely archived transaction database
is always available with simple and intuitive "easy
access" technology. "Control Master" is
also capable of stand alone operation (without the PC)
using the on board 2000 transaction battery protected
database, printing individual tickets or reports on either
the PC default printer or dedicated 40 column units,
dispensing to all outlets simultaneously, tracking oil
useage by numerous parameters and tank levels by dead
reckoning.
An advanced fluid management system that allows the dispensing
of multiple fluids at multiple locations simultaneously.
Complete management of every mechanic, every vehicle,
every drop of fluid, including waste fluids. A system
that streamlines the computer accounting process and
provides management data.
"Control Master - Never
Lose A Drop!" |
1060
1060-3 |
Digital Fluid Control
Modules
Model 1060
Directs one fluid to up to ten different locations. 40
watt transformer, surge suppressor, CSA approved, 24
volt A.C. wiring.
Model 1060-1
With key lock - special order
Dual Product Model
Model 1060-3
Directs two fluids to up to six different locations for
each fluid. Running product total for each product. Simple
toggle switch for product selection with indicator light
for each product.
DFC control modules available 24 VDC - special order.
Note: DC solenoids do not operate in AC systems
AC solenoids will not operate in DC system. |
|
RFX Control
System
One “RF” keypad controls up to 8 fluids and 48 simultaneous dispense outlets. Ticket printer provides written record of each transaction.
“RF” Meter Control Handle with rigid outlet allows designated dispensing. Uses AA batteries, easy to replace.
- Wireless communications between“RF” keypad controller and “RF” meter handle. Up to 300ft.
- “RF” system automatically seeks open channels to eliminate any interference.
- Operator and supervision security levels to determine who may use, monitor, and program the system.
- Accurate accounting and recording for dispensed fluids. Up to 8 fluids and 48 simultaneous dispense outlets.
- No hard wiring necessary for installation of system.
- Ideal replacement for old fashioned hard wired mechanical single dispense systems.
Model 2190
Code No. 2796
“RF” Keypad controller with antenna and ticket
printer.
Model 2188
Code No. 1328
“RF” meter control handle with swivel and
rigid outlet.
|
|
Impulse Meter
Model 1061
1/2" inlet, measures in quarts. One per fluid pump
required.
Model 1062
1/2" inlet, measures in pints. One per fluid pump
required.
Model 1066
1/2" inlet, measures in liters. One per fluid pump required.
Model 1071
1/2" inlet, 100 pulse unit, for Control Master system only. |
|
Fluid Solenoid
Model 1065
1/2" inlet, High Pressure, 24 VAC. One per controlled outlet location required.
Note: AC solenoids operate in DC systems when installed
with correct polarity. |
|
Ready Light
Model 1068
One per controlled outlet location required. |
|
"Y" Strainer
Model 1069
With fine mesh filter. Recommended for installing ahead of fluid solenoid to prevent fouling. 1/2" NPTF |
|
Air Solenoid
Model 1064
1/2", 24 VAC, One per fluid pump required.
Note: AC solenoids operate
in DC systems when installed with correct polarity. |
|
Pressure Relief Valve
Model 1063
3/4" inlet and 1/2" outlet
Model 1070
3/8" inlet and 1/4" outlet (for diaphram pumps only) |
|
Call Samson at 1-800-311-1047
for assistance and support in putting together
the proper and complete components necessary
for a customized fluid management and inventory
control system. We will put together a complete
Bill of Materials for you. |
|
